2pcs Load Resistor 50W 6RJ LED Decoder Fix Error Code Hyper Flash Turn Signal

Description: 2pcs Load Resistor 50W 6RJ LED Decoder Fix Error Code Hyper Flash Turn Signal Product Overview Detailsdescription2pcs Load Resistor 50W 6RJ LED Decoder Fix Error Code Hyper Flash Turn Signal Voltage: 12 VResistance: 6 ohmDimension: 15 W * 50 L (mm) Hole ID: 3 mm Did you purchase or install a set of LED Turn signals and now you have hyper flash? You need a pair of these load resistors! These resistors are spliced in parallel with the LED bulb to add extra electrical load (power dissipation) to the circuit, thus reducing blinking speed to normal rates. These are for turn signal blinker circuits ONLY. They are not designed to have current running through them for long periods of time, they will get EXTREMELY hot if you do so. This may cause fire or damage to surrounding components and the resistor itself. ONLY USE ON PULSED TURN SIGNAL SIGNAL / BLINKER CIRCUIT. NOT FOR parking or DRL USE. Load Resistor Fix LED Bulb Turn Signal Fast Hyper Blink 50W 6 OHM Features:100% brand new and high quality.Can be used with vehicle turn signal light's LED conversionSolve hyper flash or no blinking of turn signalEach LED bulb installation requires one resistor connected in parellelFix blinker flash error, hyper or error flashing of LED turn signal, parking / driving running light or license plate lightIt works as warning canceller, decoder, capacitor, or blinker rapid Flash Equalizer for LED light bulb such as 1156, 1157, 3156, 3157, 7440, 7443 or etc. Specifications:Material: AlloyColor: Gold & redQuantity: 1Pcs Features:1. These load resistor can solve common SMD LED bulb turn signal problems.2. Will help to simulate the load and heat as traditional filament light bulbs. Package included: load resistors * 2pcsT-Tap * 4 pcs Friendly Reminder:PLEASE DO NOT MOUNT TO PLASTIC It Will Melt. Common Questions & Answers: Q: I installed the load resistors but they didn't make any difference, the LED lights are still flashing fast, what can I do?A:First, check that the wires are connected securely. Sometimes the connectors (t-shaped) may not have spliced the wires completely to establish contact with the copper wire. You will have to squeeze the connectors harder. If the load resistor works, the metal part will become warm in about 30 seconds and slowly getting hotter. Second, make sure to connect the wires correctly, especially for the bulbs that have 3 wires(e.g. 1157, 3157 & 7443).Q: I have changed front and back turn signal light to LED, how many load resistors should I need?A: EACH bulb needs 1 load resistor. You need 4 pcs of load resistors for 4 bulbs.Q: There are 3 wires coming from the light with color red, black and purple on the right and red, black, and green on the left. I have no idea which two wires to put the load resistors on.A: As to which colored wire is the correct one, it is simply a trial-and-error process. Normally, black is ground, red for parking light, the remaining colors should be the turn signal. Usually the turn signal light will differ on both sides to help distinguish them from parking lights. In your case, the two turn signal wires should be purple and green.Q: Would I need resistor in back up lights to control the flow of juice to leds?A:It is highly recommended that you add load resistors to all led lights.Q: I have changed my brake light to LED recently, but "bulb out" message appeared on dashboard. will the load resistors fix the problem?A: Yes. The load resistor is specifically designed to represent the same power-draw as a standard filament bulb so that the vehicle does not mistake the lower power draw of an LED bulb as a bulb that is burnt out or missing.Q: Why do my LED turn signals flash faster than my stock bulbs?A: This is known as "hyper flashing" or "rapid flashing". Since the wattage of LED bulb is much lower than stock filament bulb, the load resistor will draw out the residual wattage from circuit to LED bulb and thus the LED bulb will function like the stock filament bulb.Q: The load resistors are very hot, is it normal?A: Yes, the load resistor will become very hot under normal operation.Therefore, it is important to mount the load resistors to metal and do not install on/near painted surfaces, plastic or wires. THEY WILL MELT! Shipping PolicyPayment MethodReturns PolicyShipping Policy Payment MethodThis is the description of Payment Method. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Returns PolicyThis is the description of Returns Policy. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Copyright©2018 DataCaciques2pcs Load Resistor 50W 6RJ LED Decoder Fix Error Code Hyper Flash Turn SignalHomePaymentReturn PolicyAbout usContact us Product Overview Detailsdescription2pcs Load Resistor 50W 6RJ LED Decoder Fix Error Code Hyper Flash Turn Signal Voltage: 12 VResistance: 6 ohmDimension: 15 W * 50 L (mm) Hole ID: 3 mm Did you purchase or install a set of LED Turn signals and now you have hyper flash? You need a pair of these load resistors! These resistors are spliced in parallel with the LED bulb to add extra electrical load (power dissipation) to the circuit, thus reducing blinking speed to normal rates. These are for turn signal blinker circuits ONLY. They are not designed to have current running through them for long periods of time, they will get EXTREMELY hot if you do so. This may cause fire or damage to surrounding components and the resistor itself. ONLY USE ON PULSED TURN SIGNAL SIGNAL / BLINKER CIRCUIT. NOT FOR parking or DRL USE. Load Resistor Fix LED Bulb Turn Signal Fast Hyper Blink 50W 6 OHM Features:100% brand new and high quality.Can be used with vehicle turn signal light's LED conversionSolve hyper flash or no blinking of turn signalEach LED bulb installation requires one resistor connected in parellelFix blinker flash error, hyper or error flashing of LED turn signal, parking / driving running light or license plate lightIt works as warning canceller, decoder, capacitor, or blinker rapid Flash Equalizer for LED light bulb such as 1156, 1157, 3156, 3157, 7440, 7443 or etc. Specifications:Material: AlloyColor: Gold & redQuantity: 1Pcs Features:1. These load resistor can solve common SMD LED bulb turn signal problems.2. Will help to simulate the load and heat as traditional filament light bulbs. Package included: load resistors * 2pcsT-Tap * 4 pcs Friendly Reminder:PLEASE DO NOT MOUNT TO PLASTIC It Will Melt. Common Questions & Answers: Q: I installed the load resistors but they didn't make any difference, the LED lights are still flashing fast, what can I do?A:First, check that the wires are connected securely. Sometimes the connectors (t-shaped) may not have spliced the wires completely to establish contact with the copper wire. You will have to squeeze the connectors harder. If the load resistor works, the metal part will become warm in about 30 seconds and slowly getting hotter. Second, make sure to connect the wires correctly, especially for the bulbs that have 3 wires(e.g. 1157, 3157 & 7443).Q: I have changed front and back turn signal light to LED, how many load resistors should I need?A: EACH bulb needs 1 load resistor. You need 4 pcs of load resistors for 4 bulbs.Q: There are 3 wires coming from the light with color red, black and purple on the right and red, black, and green on the left. I have no idea which two wires to put the load resistors on.A: As to which colored wire is the correct one, it is simply a trial-and-error process. Normally, black is ground, red for parking light, the remaining colors should be the turn signal. Usually the turn signal light will differ on both sides to help distinguish them from parking lights. In your case, the two turn signal wires should be purple and green.Q: Would I need resistor in back up lights to control the flow of juice to leds?A:It is highly recommended that you add load resistors to all led lights.Q: I have changed my brake light to LED recently, but "bulb out" message appeared on dashboard. will the load resistors fix the problem?A: Yes. The load resistor is specifically designed to represent the same power-draw as a standard filament bulb so that the vehicle does not mistake the lower power draw of an LED bulb as a bulb that is burnt out or missing.Q: Why do my LED turn signals flash faster than my stock bulbs?A: This is known as "hyper flashing" or "rapid flashing". Since the wattage of LED bulb is much lower than stock filament bulb, the load resistor will draw out the residual wattage from circuit to LED bulb and thus the LED bulb will function like the stock filament bulb.Q: The load resistors are very hot, is it normal?A: Yes, the load resistor will become very hot under normal operation.Therefore, it is important to mount the load resistors to metal and do not install on/near painted surfaces, plastic or wires. THEY WILL MELT! Shipping PolicyPayment MethodReturns PolicyShipping Policy Free Standard Shipping (Estimated between 2 to 5 Days)Payment MethodReturns Policy30 days returns. Buyer pays for return shippingHomePaymentShoppingAbout UsContact UsOn Sep 4, 2024 at 03:22:11 PDT, seller added the following information:

Price: 5.8 USD

Location: Brooklyn, New York

End Time: 2024-11-04T04:41:05.000Z

Shipping Cost: 0 USD