6-18 HP 2/ 4Stroke Water Air Cooling HANGKAI Outboard Motor Fishing Boat Engine

Description: HANGKAI 3.5-18HP 2/4 Stroke Outboard Motor Fishing Boat Engine Water/Air Cooling Cylinder Scoring is a serious damage,which caused by improper use and will cost you a lot of money to repair the motor. Don't do the following will avoid cylinder Scoring: 1start the motor on bank 2, use the motor when it stop coming out of water Even if you want test the motor, it should be done in the river! 1.About the noise: all the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon 2.The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same when one person on it or 4 people on it . Customer who has high expectations o6-18 HP 2/ 4Stroke Water Air Cooling HANGKAI Outboard Motor Fishing Boat EngineDescriptionHANGKAI 3.5-18HP 2/4 Stroke Outboard Motor Fishing Boat Engine Water/Air Cooling Cylinder Scoring is a serious damage,which caused by improper use and will cost you a lot of money to repair the motor. Don't do the following will avoid cylinder Scoring:1start the motor on bank2, use the motor when it stop coming out of waterEven if you want test the motor, it should be done in the river! 1.About the noise: all the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon 2.The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same when one person on it or 4 people on it . Customer who has high expectations on speed, please be noticed 3.It can be marched with inflatable boats, rubber boats or fishing boats 4.Necessary: you have to prepare a boat-motor stand or Hanging board on your boat MODEL ONE: 3.5HP & 2-Stroke(TYPE ONE) Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us).our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!! About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.SKUOT-028 Two strokes 3.5 hp and 3.6 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode STRICTLY FOR PROFESSIONAL USE ONLY Please Note: There are two pull starter included in the parcel(one is the machine, another one for spare) We don't supply wearing parts (pull starter)for free. If you want buy one please click: Description: Overall length:92CM Overall widteh:36.5cm Overall height:22cm Transom height:42cm Full throttle perating range:4000-5000r/minMAX SPEED4000~5000rpmMaximum output:2.5kw(3.5HP) Speed:10km/h Type:2-strokeShort shaft 40cm Ignition system: CDI system Starting system: Manual start Staring carburetion system: Choke start Propeller mark:7-1/45-A(inch) The engine and the propeller ratio:2:1 Recommended fuel: Regular unleaded gasoline Fuel to oil ratio: 35:1 Please be suject to this version, and disregard the manual about this point Gear ratio: 27/13 Maximum speed: 10 km / h Built-in fuel tank: 1.3L Fuel consumption per hour: 1.5L When at normal cruising, the appearance of the seventh picture. Falling back the boat, the appearance of the outboard motor likes the eighth picture . Falling back the boat, you should drive slowly otherwise the boat will not stable. The outboard motor backet can revolve 360. Only in simple let the engine revolve 180 and the operation handle face back, the boat can fall back to drive. Announcements: After in the sea water or turbid water cruising 1.Use the fresh water cleaning the outboard motor 2.With the moderate velocity circulating the engine,cool off the water chanel with fresh water. 3.Before completely running out cooling water,don't put the outboard motor outside. Otherwise the water cam pass the exhaust port to enter the air cylinder, from that will cause the engine breakdown. 4.The engine should deposit in the aridity and ventilated well place,avoid exposing directly in the sunshine. 5.Before the long term storing,you should run out of the gasoline in the fuel tank. MODEL TWO: 3.6HP & 2-Stroke Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us).our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!! About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding. SKU:OT-ML-132 Two strokes 3.5 hp and 3.6 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode STRICTLY FOR PROFESSIONAL USE ONLY 1.Start-In-Gear protection/clutch feature prohibits prop rotation while idling2.Lift/Tilt feature for shallow water operation and convenience3.Features 360 degree steering rotation for reverse without gear shifting4.Superior engine water cooling system for improved engine performance5.Easy pull off engine cover with push button latch for instant motor accessProduct DescriptionMAX SPEED4000~5500rpm Short shaft 40cm Features: Features 360 degree steering rotation for reverse without gear shifting . Start-In-Gear protection/clutch feature prohibits prop rotation while idling . Lift/Tilt feature for shallow water operation and convenience . Superior engine water cooling system for improved engine performance . Easy pull off engine cover with push button latch for instant motor access . Standard CDI ignition system for easy starting and improved performance . Vertical mount engine design for increased power, performance and durability . Superior carbonation system with primer bulb for increased efficiency . Twist grip throttle handle and engine stop button for improved response . Superior outboard anti corrosion system and anodes for increased durability . Durable cast Nylon plastic construction for superior corrosion protection . Through the prop exhaust outlet for decreased noise and pollutant . Heavy duty lightweight Nylon plastic cast propeller is standard equipment Shipping Weight: 21.4 pounds MODEL THREE:3.5HP & 2-Stroke (TYPE TWO) Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!! About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.SKUOT-ML-279 Two strokes 3.5 hp and 3.6 hp are controlled by the handle, which is operated by the clutch. There is no Neutral, only idle mode or low speed mode Please Notice:STRICTLY FOR PROFESSIONAL USE ONLY What you will receive is our new version of this boat engine The trademark will be Yadao instead of Speeda.Overall length:92CM Overall widteh:36.5cm Overall height:22cm Transom height:42cm Full throttle perating range:4000-5000r/minMAX SPEED4000~5000rpm Maximum output:2.5kw(3.5HP) Speed:12km/h(four people) Type:2-strokeShort shaft 40cmIgnition system:CDI system Starting system:Manual start Staring carburetion system:Choke start] Propeller mark:7-1/45-A(inch) The engine and the propeller ratio:2:1 Recommended fuel:Regular unleaded gasoline Fuel to oil ratio: 35:1 Please be suject to this version, and disregard the manual about this point Gear ratio: 27/13 When at normal cruising,the appearance ofthe seventh picture. Falling back the boat, the appearance of the outboard motor likes theeighth picture . Falling back the boat, you shoulddrive slowly otherwise the boat will not stable. Theoutboard motor backet can revolve 360. Only in simple let the engine revolve 180 and the operation handle face back,the boat can fall back to drive. Announcements After in the sea water or turbid water cruising 1.Use the fresh water cleaning the outboard motor 2.With the moderate velocity circulating the engine,cool off the water chanel with fresh water. 3.Before completely running out cooling water,don't put the outboard motor outside. Otherwise the water cam pass the exhaust port to enter the air cylinder, from that will cause the engine breakdown. 4.The engine should deposit in the aridity and ventilatedwell place,avoid exposing directly in the sunshine. 5.Before the long term storing,you should run out of the gasoline in the fuel tank. MODEL FOUR:4HP & 4-Stroke OT-ML-277Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!! About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding. STRICTLY FOR PROFESSIONAL USE ONLY Type: 4 stroke 4 horsepowerShort shaft 40cm Capacity: 52cc Transmission ratio: 2.08 (27:13) The number of cylinders: 1 MAX SPEED4500~5500rpm Maximum power: 2.8 kW /4 HP Shift position: clutch control Package volume: 95x40x30 cm Ignition system: CDI Cooling system: air cooling Starting method: Manual start Refueling: No. 93 gasoline Propeller size: 7 1/4X7-A The maximum fuel consumption: 1.4 liters / hour Recommended Lubricant:4 stroke lubricating oil Mixing ratio:Pure gasoline Trim and tilt system:Manual Tilt Start-In-Gear protection/clutch feature prohibits prop rotation while idling convenience Features 360 degree steering rotation for reverse without gear shifting Cooling system: air cooling Easy pull off engine cover with push button latch for instant motor access MODEL FIVE:6HP & 2-Stroke OT-C001-073 Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!! About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding STRICTLY FOR PROFESSIONAL USE ONLYTechnical Parameters Dimension Overall length 1040mm(40.9 in) Overall width 872mm(34.3 in) Overall height 332mm(13.1 in) Transom height 44CM(17.3 in)Short shaft 40cm Performance Full throttle operating range 5000-6000r/min MAX SPEED4500~5500rpm Maximum output 4.4KW/6HP Idling speed ( in neutral) 1000±100 r/min Engine Gear positions Forward-neutral-reverse Gear ratio 2.15(28/13) Trim and tilt system: Manual tilt Drive unit Recommended fuel Regular unleaded gasoline Integral fuel tank capacity 2.5L Recommended engine oil 2-stroke outboard motor oil Engine oil type Genuine or recommended 2str engine oil Lubrication System Engine oil mixed gasoline Engine oil mixing ratio Fuel 50: Engine oil 1 Gear oil quantity 195ml(6.6 fl.oz.) Tightening torque for engine Spark plug 25.0Nm(18.4 ft-lb) (2.55 kgf-m) Engine oil drain bolt 18.0Nm(13.3 ft-lb) (1.84 kgf-m) MODEL SIX:7HP & 4-StrokeOT-ML-278 Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period (10 hours). (If you do not know how to handle this, please contact with us.) About certification:We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.About the noise: 1. All the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon 2. The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same when one person on it or 4 people on it . Customer who has high expectations on speed, please be noticed.3. It can be marched with inflatable boats, rubber boats or fishing boats.4. Necessary: you have to prepare a boat-motor stand or Hanging board on your boat.Note:Must read before use!Four stroke 7 hp:Firstly, Fill the gear oil (open gear box lid and fill it).Secondly, Fill NO. 92 petrol, lightly press oil pump 6-10 times.Thirdly, Fill engine oil don't exceed the head of the pattern.Forthly, Pull the gear to netural gear, and plug the brake line in, hang the other side of the brake line on your wrist at the same time.Then, turn the accelerator gets up to 50% and rapidly pull the starter line.After the motor start , please turn the gear to minimum before put another gear.Otherwise, the gearwheel will be broken if you put high gear. Description:Universal motors, high performance, reliable quality· Perfect match inflatable boats, fishing boats, sailboats, and small yachts.· Economical and compact structure. Durable, lightweight and anti-corrosive construction.· Maneuverable and safe twist grip throttle control.· Suitable for: Freshwater and saltwater· One year warranty covers the motor, to provide parts freeType: 4 stroke 7 horsepowerCapacity: 196CCTransmission ratio: 2.08 (27:13)The number of cylinders: 1Maximum speed: 4500-6000rpmMaximum power: 5.1 kW /7 HPShift position: clutch controlPackage volume: 120x60x42.5 cmIgnition system: TCICooling system: air coolingStarting method: hand startRefueling: No. 93 gasolinePropeller size: 3-7 1/2''x5''Gear position: F-N-RControl system: Tiller controlN.W./G.W.: 26.7/31.7kgsRecommended Lubricant: 4 stroke lubricant oilTrim and tilt system: Mannual tiltStandard fuel tank capacity: 1.4L/withinlong shaft 50.8CM MODEL SEVEN: 6.5 HP & 4-Stroke OT-ML-282 Notice:Please add gear oil to the gears before use the motor and replace gear oil after the run-in period(10 hours).(if you do not know how to handle this,please contact us) .our outboard motor doesn't with oil of gear,please prepair it by yourself .Keep in mind that you must add oil on the gear beofore use !!! About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding.The Hangkai 6.5 hp 4-stroke provides all the power you need for motoring in a small craft. This engine does that as well as providing fuel efficiency second to none and a newly redesigned carrying handle and holding grip make it convenient to transport! With all of this available at a competitive price, it is no wonder this little outboard receives so much attention and praise! Brand: HANGKAI Displacement: 123CC Gear ratio: 2.08(27:13) Cylinder: 1 Max.Output(kw): 4.8 Max.speed(r/min): 5000-6000 Gear Positions: F-N-R Packing size: 114x64x41cm Ignition System: CDI Cooling System: Water-coolingShort shaft 40cm Control System: Tiller control Starting System: Manual start Control System: #93 gasoline N.W./G.W.(kgs): 26/31.2 Bore x Stroke(mm): 59x45 Recommended Propeller range: 3 -7"x9" Recommended Lubricant: Four Stroke Lubricating oil Mixing ratio: Pure gasoline Trim and tilt system: Manual Tilt Overall LxWxH(cm): 78.3x34.3x103.9 Standard fueel tank capacity: 12L Optional fuel tand capacity: / Bonus accessories: brochures, tubing, cotter pins Pump impeller, start rope, start key 12 liter fuel tank, tool kit, spark plug, cylinder head pad "Quality of life, starting from here!" ——In this store, we have selected a series of high-quality products for you, Make your shopping experience more enjoyable. Come and buy now, enjoy a worry free life! Welcome to cdyjwl555!! Thank you for your support! If you have any questions,please feel free to contact us!!! Marine 12V 40/45/58/65LBS Electric Outboard Trolling Motor for Fishing Boat Kayak CE Pay Attention 1.About the noise: all the gasoline machines are noisy, currently we did not test the decibel , but the noise is the same as the motorcycle, so it is a normal phenomenon. 2.The machine itself is lightweight, it can use on boat weight of 100kg or less , load-bearing 4 people, but the speed is certainly not the same whenone person on it or 4 people on it . Customer who has high expectations on speed, please be noticed. 3.It can be marched with inflatable boats, rubber boats or fishing boats. 4.Necessary: you have to prepare a boat-motor stand or Hanging board on your boat. About certification: We can only provide CE certification, there is no other certification can be provided,thanks for your understanding. MODEL ONE: 40 LBSSpecifications Model：L40Thrust（kg）:It is recommended to propel small boats weighing less than 200kgSpeed control: F5-R2Motor type: Brush motorRated voltage(V):12Rated speed(R/min):1700Rated current(A):34Rated power(W):408Control handle: Telescopic typeMaximum speed(km/h):6Noise DB:50dbN.W./G.W.(kgs)7.8/9.3（17.2/20.5lb）Propeller model(in):3 leaves/9Packing size(cm):102*41*16（40.16*16.14*6.30inch）Battery model recommendation:Choose 12V 100A batteries, the maximum power of 3 hours of sustainable operation.Package Include:·1x Trolling Motor·1x Operation ManualMODEL TWO 45LBS Product Specifications: Short Shaft:40cmBrand: Hangkai Model: ET45L Thrust (kg): 20 Seep control: F5-R2 Motor type: Brush motor Rated voltage (V): 12 Rated speed (R / min): 1300 Rated current (A): 52 Rated power (W): 552 Control handle: telescopic Maximum speed (km / h): 8 Noise DB: 50db N.W./G.W.(kgs) 9/10 Propeller model (in): 3 leaves / 10.6 Packing size (cm): 107 * 55 * 17.5 Battery Type Recommended: Choose 120A battery, the maximum power of 3 hours sustainable operation. Package Included: · 1x tugged motorMODEL THREE:58LBSSpecificationsShort shaft ：40cmBrand：SUNELEXEModel：L58Speed control: F5-R2Motor type: Brush motorRated voltage(V):12Rated speed(R/min):1700Rated current(A):51Rated power(W):612Control handle: Telescopic typeMaximum speed(km/h):10Noise DB:50dbN.W./G.W.(kgs)10/11Propeller model(in):3 leaves/10.6Packing size(cm):101*46*16CM(39.76*18.11*6.29inch) Thrust 58 lb Battery model recommendation:Choose 12V 150A batteries, the maximum power of 3 hours of sustainable operation. Package Include:1 x Trolling Motor1 x Operation ManualMODEL FOUR:65LBS SpecificationsBrand：Hangkai Model：ET65L Shaft Type：stainless steel Shaft type(inch / mm)：≈15.7″/ 400mm Shaft Length :15.7 "(400 mm)/Short shaftThrust Level : 65 pounds (lbs) thrust Thrust（kg）:30 Seep control: F5-R2 Motor type: Brush motor Rated voltage(V):12 Rated speed(R/min):1420 Rated current(A):55 Rated power(W):660 Control handle: Telescopic type Maximum speed(km/h):11 Noise DB:50db N.W./G.W.(kgs)10/11 Propeller model(in):3 leaves/10.6 Packing size(cm):107*55*18 Battery model recommendation: Choose 120A batteries, the maximum power of 2.5 hours of sustainable operation. Package Include:· 1x Trolling Motor · 1x Operation Manual

Price: 106.99 USD

Location: Chino, California

End Time: 2024-10-01T05:29:32.000Z

Shipping Cost: 0 USD