Dental Ortho Bonding Light Cure Resin Composite Kit/ LED 1S Curing Light Lamp

Description: Dental Ortho Bonding Primer Brackets Light Cure Adhesive Paste Syringe Kit (Standard version ) Warning: Ortho-Bonding primer and adhesive contains acrylate monomers. Acrylate monomers are known to produce allergic skin reactions in certain sensitive individuals. May cause eye and skin irritation. Precautions: A void eye and skin contact. Wear gloves when handing this material. Precaution: Please follow manufacturer's directions on the handing, proper use and recommendations for eye protection, when using a curing light. This system is designed to be used at room temperature (20-25°C, 68-77°F) Storage between 2-27°C/35-80°F Light Sensitive Contents: 3 x Adhesive paste Syringes (10.5g) 1 x Primer Bottle (8ml) 40 x Brushes 1 x Instruction Booklet Description：(Mini version) Warning: Primer and adhesive contains acrylate monomers. Acrylate monomers are known to produce allergic skin reactions in certain sensitive individuals. May cause eye and skin irritation. Precautions: Avoid eye and skin contact. Wear gloves when handling this material. Precaution:Please follow manufacturer's directions on the handling, proper use and recommendations for eye protection, when using a curing light This system is designed to be used at room temperature (20-25°C, 68-77°F)。Storage between 2-27°C/35-80°F Light Sensitive Packing List: 1 x Adhesive paste Syringes(3.5g) 1 x Primer Bottle (3ml) 1 x Instruction Booklet 20 x Brushes Cordless Dental Light Cure Lamp Light Metal Head LED 1S Curing Light Product DescriptionParameterWavelength440-480nmLight power5WIntensity800-1400mw/cm²BatteryLi-on 800mAhInput voltageAC100-240V, 50/60Hz 0.4A MaxOutput voltageDC 5V/1.5ANet Weight155gMode selectionP1, P2, P3Solidification time1S,3S,5S,10S,15S,20SFeatures:·Produce the maximum light intensity safely.· A high intensity of 1400 mW/cm2.· Offers extremely short curing times of no more than 3 seconds.· Cordless, highly portable and light weight (only 155g).· High-performance Li-ion battery technology.· LED panel conveniently indicates a countdown curing time.· Battery can be fully recharged in 90 minutes.· Battery with protection against over-voltage, over-current and short circuit.· 3 versatile curing modes for every indications.· Automatic power off, low battery alert.· Color : White . Operation conditions:1.Storage Condition: Temperature: +10+402.Humidity: 30%-75%3.Atmospheric pressure: 70KPa-106Kpa4.Environment Conditions: Not near from fire equipment or flammability material. Packing list:The host * 1Metal lamp holder *1The silicone base *1Power adapter *1Disposable protective sleeve *1Shade plate *1Product specification *1 DX.Universal Dental Light Cure Composite Resin Kit Shade Etching Gel Adhesive INDICATIONS FOR USE:Direct restoration for all class caries.Restoration of teeth defect and veneer. REFILL:Light Cure Composite: 4g/Syringe*5Syringe Needles : 5pcs/ box*1Total Etching Adhesive: 5ml/Bottle*1Etching Gel: 2.5ml/Syringe*1Applicators Brushes: 20pcs/box*1Net weight: 188.4gCOLOR: A1,A2,A3,A3.5,B1 FEATURES & ADVANTAGES:Unique dispersion technology ensure the filler evenly distributedRadioopaque and fluoride releasing Optimal polishability and high shade stability.Excellent handling, not sticky to instrument;Suitable for most cases of restoration, extensive indication of usage. INSTRUCTIONS:(1) Preparation: isolate and prepare tooth.(2) Cleaning: rinse the preparation with water.(3) Drying: gently air dry until there is no visible water.Do not allow enamel or dentin to dry for an excessive period of time.(4) Applying Dentex Self-Etching Light Cure Adhesive (DSA): dispense 1-2 drops of DSA into a mixing well, apply enough DSA to the entire preparation with a little brush until a shiny surface is achieved and then wait for 10 seconds (DSA should not be applied too much ). Use a gentle stream of air to evaporate the solvent for 5 seconds. (If using a non self-etching adhesive, an etching step should be used according to the manufacturer's instruction).(5) Cure: light cure for 20 seconds at 500±50mW/cm2. Keep the distance to exposure surface less than 4 mm.(6) Applying Dentex light cure composite (DLC): place selected DLC into cavity preparation following by light cure. According to following table, the curing time is recommended for different depth and color shades. In order to reduce shrinkage stress, for a large cavity, an increment filling is recommended. In general, 1-2 mm increments are placed into cavity preparation from different sides and the restoration is built incrementally. Each increment is light cured for 30 seconds.(7) Finishing: after light cure, adjust restoration.(8) Polishing: use polishing strip or disc to polish the surface WARNING:Do not use this product for patient who is allergy to methylmethacrylate. Do not use this product with any material contained eugenol. PRECAUTIONS:Methmethacrylate resins may cause skin sensitization in susceptible persons. In case of tell, wash skin with soap and water. In severe situation, get medical attention. ATTENTION:To an exposed pulp, a pulp capping material such as Calcium hydroxide may be used before using this product. STORAGE:Store at 25℃ or less in a cool and dry place and avoid direct sun exposure.Recap the syringe after use.DISPOSAL: After the product is used up, dispose it as normal medical rubbish.SHELF LIFE: 3 years Quantity: 1 Kit. ********************************************************************** Dental Orthodontic Adhesive Light Cure Band Cement Blue Glue Feature: This orthodontic adhesive provides a longer working time and a rapid setting time. Can be placed directly into bands. Excess flash is easy to clean up prior to the light curing and the cement is easy to see due to the blue color. It contains fluoride to reduce the chance of declacification. Packing list of one pack 1 x Etchant acid Gel 2.5ml syringe; 1 xLight Cure Adhesive Paste 5g syringe; 1 x Syringe tip Box size: 17*11*2.5cm STORAGE: Store at 25℃ or less in a cool and dry place and avoid direct sun exposure. Recap the syringe after use. FDA for Tooth Bonding: 510(K)Number: K232978, Regulation Number: 872.3200, Product Code: KLEFDA for Resin: 510(K)Number: K180463, Regulation Number: 872.3690, Product Code: EBFThis product expires on 05/2025 or better.FDA for Tooth Bonding: 510(K)Number: K232978, Regulation Number: 872.3200, Product Code: KLEFDA for Resin: 510(K)Number: K180463, Regulation Number: 872.3690, Product Code: EBFThis product expires on 05/2025 or better.

Price: 21.99 USD

Location: Fullerton, California

End Time: 2024-12-26T04:28:03.000Z

Shipping Cost: 0 USD