Eastwood Burgundy Sunset 3:1 Acrylic Urethane Single Stage Paint 96 oz

Description: Eastwood Burgundy Sunset is a maroon color is a good option for those times when the classic Quarter Mile Candy Red is just too light.Catalyzed urethane for unsurpassed durabilityHighly resistant to UV rays, chemicals, chipsMakes 1 sprayable gallon when mixed 3:1 with a required activatorApproximate Coverage: 125 Sq FtMax Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting This premium 2-component topcoat system is blended with top-quality raw materials and advanced composition coatings technology. Superior to acrylic, alkyd and lacquer coatings. Eastwood's single-stage urethane paints hold their gloss longer and won't yellow. Pro Tip: When spraying Single Stage Metallic and Pearl Paints, you can improve appearance by using the special additive Metalli-Flow Metallic Paint Enhancer to help lock and stabilize metallic and pearl particles for a perfect finish.SpecificationsSINGLE-STAGE PAINT MIXING RATIOS Thoroughly mix three parts single-stage urethane paint with one part Activator. No additional reduction is required but can be used as needed. Use caution in mixing materials as Eastwood's single-stage urethane paint may begin to gel after approximately two hours (at 70° F)PAINT GUN SET-UP HVLP Gun: Fluid Tip 1.3-1.5 mm Inlet Spray Pressure 25-30 PSI, Conventional Gravity: Fluid Tip 1.3-1.6 mm Inlet Spray Pressure 45-50 PSI, Conventional Siphon: Fluid Tip: 1.4-1.8 mm Inlet Spray Pressure 45-50 PSIAPPLICATION INSTRUCTIONS Apply single-stage urethane paints in two to three medium wet coats as necessary to achieve sufficient coverage, allowing ten minute flash between coats. Additional coats may be necessary to achieve total coverage for some metallic colors. A final "fog coat" may be applied with metallic colors to help set an even flake pattern and /or adjust flake orientation. A dry film thickness of approximately 2 mil is recommended. Paint should be dust free within 10-15 minutes and tack-free within one hour (at 70° F). Re-coat anytime after the previous coat has flashed, or before 18 hours. After 18 hours, paint should be abraded prior to re-coating for proper adhesion purposes. This urethane paint may be applied as a stand-alone single-stage system, or in combination with Eastwood's High Solids Urethane Clear as a basecoat/clearcoat system. Additionally, Urethane Clear may be integrated into Urethane color. When combining the two systems, be sure to activate each side (the paint and the clear) separately, with their own activators at the correct mix ratios, before blending. When used as a Single-Stage Urethane Paint, this coating may be wet-sanded and polished for increased depth and gloss like any other urethane topcoat. Care should be taken when lightly cutting metallic colors to prevent disturbing aluminum flake.Compatible Activators Slow-21856ZP, Medium-21853ZP, activators are sold separately *** THIS PAINT REQUIRES AN ACTIVATOR TO CURE PROPERLY THAT IS NOT INCLUDED *** 3:1 Single Stage Paints must be mixed one with these activators 21853ZP Eastwood 3:1 Single Stage Urethane Slow Activator 1 Quart 80 Degree And Above 21856ZP Eastwood 3:1 Single Stage Urethane Medium Activator 32 Oz 70 To 80 Degree Compatible Paint Reducer 50104ZPSafety Information Always wear proper eye, skin and respiratory protection. Always paint in a well-ventilated area away from sparks and open flame. Consult MSDS and product data sheets for proper safety precautions. Cancer and Reproductive Harm - www.p65warnings.ca.gov

Price: 203.99 USD

Location: Pottstown, Pennsylvania

End Time: 2025-01-08T07:13:32.000Z

Shipping Cost: 0 USD