For MERCURY 40 two stroke ( 2-CYL ) Vinyl decal set from BOAT-MOTO / sticker kit

Description: For the 2-stroke outboard engine MERCURY 40 a set of vinyl stickers from the graphics studio "BOAT-MOTO".( 2-CYL )For Top Cowling - 821528T5, 821528T7Digital printing and lamination, is a reproduction. Stickers are produced on self-adhesive vinyl film with lamination.We use only high-quality films from well-known manufacturers. Each sticker containing more than one small piece will be sealed with transfer tape.Transfer tape helps transfer glued parts to the engine without disturbing the dimensions between the stickers. Large parts of the decals are not covered with transfer tape. Stickers may differ slightly from the original in color, size, shape Each sticker containing more than one small piece will be sealed with transfer tape.Transfer tape helps transfer glued parts to the engine without disturbing the dimensions between the stickers. Large parts of the decals are not covered with transfer tape. Stickers may differ slightly from the original in color, size, shape.Waterproof, frost-resistant and heat-resistant, petrol-resistant - (if not left for a long time in a petrol environment).Stickers adhere well to paint, varnish and other cleaned smooth surfaces.When painting the upper casing, you can stick the decal on the base paint and cover the decal with clear varnish along with the engine casing.Decals are resistant to ultraviolet light, but over the years, under the influence of sunlight, over time, everything fades and loses color, be it a sticker or paint, etc. But this will not happen in the early years. 1. - Great price. 2. - Vinyl films from only the best manufacturers. 3. - There is expedited delivery. 4. - Possibility to supplement the complete set with stickers, plates on your engine, according to your photos and measurements. - Free of charge. (Send photos and measurements in a message to us). 5. - You accidentally spoiled a part of the sticker, don't worry, we can send small parts to you free of charge, you pay only 8-10 $ shipping for standard delivery or in an envelope. Send us a photo of the damaged part. 6. - Didn't find the stickers you were looking for? Send us a message with a photo. If we do not have such decals, then we will ask you to measure parts of the stickers, according to old samples. We will make the kit for free, pay only for the delivery 8-10 $. 7. - Ability to change color, font, size of decals. Instructions for correct gluing. 1. The ambient temperature is not lower than +10 C and higher.2. Prepare about 300 grams of water in the sprayer, (preferably distilled water), and add to it (pure soap without additives) a couple of drops or very finely piece of solid. Mix well.3. Prepare a felt spatula to remove from under water and air drops stickers.4. Prepare clean, non-marking wipes particles.5. Prepare Ethyl alcohol to remove fat from surface.(Attention!!! Do not ingest. Otherwise nothing further will come out.))))6. Accurately measure the place for gluing.7. Thoroughly clean the surface of the bonding area. (Napkin with ethyl alcohol.)8. Before removing small parts from the base, The transfer film must be firmly pressed against decals. And make sure small parts are attached to transfer film. Small parts with transfer film, apply on engine cover without water, dry. After that, the transfer film can be easily removed, after you transfer to the engine cover.9. Peel off the film from the back of the sticker, exposing sticky side.10. Apply spray water to large parts decals on the adhesive layer, and to the surface on which stickers will be applied.11. Paste the sticker on the surface you need, secure the sticker by pushing it into place and extrude Accumulated drops of water with a spatula, removing drops water to the edge of the sticker.12. After pasting, you need to wait about 24 hours. Attention. You do not need to test for strength. Good bonding takes 2-3 days. Worldwide shipping.__________________________________________________________________________________________________________________________TRADEMARK LAW: Protected names belong to their owners. All of the names of brands, goods or information providers mentioned in this offer belong to their owners and are reproduced without guarantee of free availability. The names are either registered trademarks or should be treated as such. Please note that the rights to all logos, brand names, trademarks, etc. lie with their respective owners. We are not liable for damage resulting from the improper use of third-party brands, even if we produced this film. The buyer declares that he is in possession of the copyright and/or trademark rights required for the services he has commissioned or, if he is not the author and/or trademark owner himself, has obtained permission from the author and/or trademark owner to use the image, trademarks and/or names. The seller does not check whether the customer is in possession of the copyright and trademark rights required for the services to be provided. Liability towards the third party with regard to copyright and/or trademark claims is therefore excluded for the services commissioned. The production takes place exclusively in and after customer order.

Price: 44 USD

Location: Merefa city, Kharkov region

End Time: 2023-11-23T00:46:47.000Z

Shipping Cost: 0 USD