OBD2 Breakout Box Diagnosis Scan Tool for Monitoring Signals of Protocol/Power/G

Description: OBD2 Breakout Box Diagnosis Scan Tool for Monitoring Signals of Protocol/Power/Grounds,Automotive OBDII Protocol Monitor. Breakout Box for OBDII Diagnostic Link Connector 【Major Function】VKALTUL automotive OBDII protocol monitor is an automotive tool for the OBDII diagnostic link connector which offers easy access to the OBDII connector for monitoring signals of protocol , power and grounds conveniently and safely . It can be also connected to multi-meter or oscilloscope for further testing once unconfirmed signals detected.【LED Indications of OBD2 Breakout Box】LEDS to quickly indicate power or ground problems of OBDII connector. When the code reader communicates with the vehicle, the yellow LED (pin 2/6/7/10/14/15) lights up and occur a waveform signal. If the car is detected grounded normally, the green LED (pin 4/5) will always be on. If the car power supply is detected as normal, the red LED ( Pin16） will always be on.【16 pins OBDII Interface】OBD interface of the breakout box adopts a 16 pins design, which completely simulates the 16 pin layout of the OBD II interface, so that more tests can be performed quickly and intuitively. Easily access each of the 16 pins while scan tool communicating with vehicle.【4MM Banana Sockets】The OBD2 breakout box set uses safety banana sockets that accept all types of 4mm banana plugs including those with safety sheaths，so as to connect to a multimeter or oscilloscope for further measurement of uncertain monitoring signals.【35.43-inch Extension Cable】The OBD2 protocol detector has male and female connectors. You can place the breakout box between the diagnostic tool and the vehicle, which makes it easier to measure the can bus signal. The cable length of OBDII diagnostic link connector is 35.43-inch, which makes equipment connection more convenient. Product Description VKALTUL breakout box is an automotive tool for the OBDII diagnostic link connector which offers easy access to the OBDII connector for monitoring signals of protocol , power and grounds conveniently and safely . It can also be connected to a multimeter or oscilloscope for more accurate testing. OBD interface of the detector adopts a 16 pins design,the input jack layout fully emulates the 16-pin layout of the OBDⅡ interface,allowing more tests to be performed quickly and intuitively, you can have quick access to all 16 pin connections during vehicle service and diagnostics. Features of Breakout Box Automotive It provides easy access to the vehicle data bus lines. LEDS to quickly indicate power or ground problems of OBDII connector. Mimics the OBDII connector layout for quick reference. Easily access each of the 16 pins while scan tool communicating with vehicle. Probing at the OBDII connector is no longer required. Quick , safe and convenient access to chassis ground and power by this monitor. Uses safety banana sockets that accept all types of 4mm banana plugs including those with safety sheaths. 16 pins OBDII Interface It is a 16-pin setup that simulatesthe OBDII interface which enablesmore tests to be performed quicklyand intuitively Red LED Signal Light If the car power supply is detected as normal, the red LED ( Pin16） will always be on. Yellow LED Signal Light When the code reader communicates with the vehicle, the yellow LED (pin 2/6/7/10/14/15) lights up and occur a waveform signal. Green LED Signal Light If the car is detected grounded normally, the green LED (pin 4/5) will always be on. The breakout box has male and female connectors. You can place the breakout box between the diagnostic tool and the vehicle, which makes it easier to measure the can bus signal. The cable length of OBDII diagnostic link connector is 35.43-inch, which makes equipment connection more convenient. Warm Tip： 1、This tool is designed for use by automotive professionals. Improper use of this tool can result in damage to the vehicle data communication system and associated circuits and systems. 2、Do not jumper pins together without understanding the circuits. 3、Do not use the tool to power up a load device exceeding 1 amp. Do not place a jumper between the power pin 16 and ground pins 4, 5. 4、When this monitor is engaged the yellow LEDS will flash when changes take placeon the corresponding data line. The flashing LEDS will allow you to determine the activity on that line. The green and red LEDS corresponding to OBDII connector pin 4, 5 and 16 are always active. Style Breakout Box 1 Product Dimensions 9.06 x 4.72 x 2.36 inches Manufacturer Part Number DY29 Item Weight 12.3 ounces Power Source 有线供电 Screen Size 35.43 Inches Shipping Fast shipping is very important for us. Our standard US shipping service is FREE. Your order will be shipped within 2-3 business days upon full payment received. Your order will be delivered within 2-3 business days after the handling time. We only ship to the confirmed PayPal address. We reserve the right to cancel any order for any reason at any time. We are not responsible for undeliverable addresses. Returns and payment We offer a 30 days return policy from checkout winning date. We allow only PayPal as payment methodFeedBack Your feedback very important to us, after you get your package and you are satisfied with our service please leave us positive feedback If you have any problem with your order / any questions please before leave any type of feedback For any questions, using eBay contact system Please visit our eBay store to check out other items for sale!Thank you for shopping at our store.

Price: 42.99 USD

Location: Derby, Kansas

End Time: 2024-11-10T08:20:26.000Z

Shipping Cost: 0 USD