STC-3018 AC 110V-220V Digital Temperature Controller Thermostat NTC Sensor US

Description: Store CategoriesStore CategoriesOtherSTC-3018 AC 110V-220V Digital Temperature Controller Thermostat NTC Sensor US Details Specfications:● Power supply: 110-220VAC ± 10%, 50/60Hz● Measurement temperature range: -50°C ~ +120°C / -58°F~248°F● Resolution: 0.1°C● Accuracy: ±1°C● Relay output contact capacity: heating: 10A/220VAC, cooling: 10A/220VCA● Sensor h type: imported NTC sensor, line length 1 meter● Shell material: gray ABS flame retardant plastic shell● Net weight 120g, Gross weight 140gInstruction:Normal mode: The red digital tube on the left shows the real-time temperature, the blue digital tube on the right shows the set temperature.Setting mode: The red digital tube on the left displays the setting mode, the blue digital tube on the right displays the setting contents.Code Instruction: Code Function Default Set Range Start or Stop Temperature 0°C/68°F -50~120°C/-58~248°F P0 Working mode H H/C P1 Difference set value 2 0.2-10 P2 High temperature alarm value 80°C/176°F -50~120°C/-58~248°F P3 Low temperature alarm value -50°C/-58°F -50~120°C/-58~248°F P4 Temperature calibration value 0 -10.0°C~10.0°C P5 Compressor delay time 0 0-60Min P6 Display mode C C/F P0: working modeThis setting is mainly set to the value when the thermostat is used for the first time. If it is used for heating, it should be set to H. If it is used for cooling, it should be set to C.P1: hysteresis settingThe hysteresis is the difference required when the thermostat reaches the set temperature and stops working again. For example, if we set the heating mode to a temperature of 37-40 degrees, then the difference is 3P2: high temperature alarm valueWhen the temperature reaches the set value, there will be an alarm action and stop working.P3: low temperature alarm valueWhen the temperature is lower than the set value, there will be an alarm action and stop working.P4: temperature correctionThese functions are used for temperature calibration. If there is a deviation between the detected temperature and the actual temperature, some functional effects can be used. The positive value = measured value + corrected value. For example, we measure the temperature at 25.6 degrees and actually 25.8 degrees. P4 can be used. Set to 0.2 then the final temperature is 25.6+0.2=25.8P5: delayed startThis function is generally used for compressor refrigeration. If you purchase some thermostats for the refrigerator freezer, this value must be set. According to the compressor back pressure, the general setting is 3-6 minutes.P6: C/F conversionIf you want to change to F value, change the unit to F, the unit display light is on. If you want to change it to C value, change the unit to C, the unit display light is not bright. If you want to convert quickly, exit the display, long press You can quickly convert units by adding 3 seconds.Package Included:1 x Temperature Controller+Waterproof Sensor Shipping PolicyPayment MethodReturns PolicyShipping Policy Payment MethodThis is the description of Payment Method. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Returns PolicyThis is the description of Returns Policy. Do not dismiss your dream.To be without dream is to be without hope.To be without hope is to be without purpose.Do not run through your life so fast that you forget not only where you have been, but also where you are going.Life is not race, but a journey to be savored each step of the way.Copyright©2017 DataCaciquesHomePaymentReturn PolicyAbout usContact usSTC-3018 AC 110V-220V Digital Temperature Controller Thermostat NTC Sensor US DetailsSpecfications:● Power supply: 110-220VAC ± 10%, 50/60Hz● Measurement temperature range: -50°C ~ +120°C / -58°F~248°F● Resolution: 0.1°C● Accuracy: ±1°C● Relay output contact capacity: heating: 10A/220VAC, cooling: 10A/220VCA● Sensor h type: imported NTC sensor, line length 1 meter● Shell material: gray ABS flame retardant plastic shell● Net weight 120g, Gross weight 140gInstruction:Normal mode: The red digital tube on the left shows the real-time temperature, the blue digital tube on the right shows the set temperature.Setting mode: The red digital tube on the left displays the setting mode, the blue digital tube on the right displays the setting contents.Code Instruction: Code Function Default Set Range Start or Stop Temperature 0°C/68°F -50~120°C/-58~248°F P0 Working mode H H/C P1 Difference set value 2 0.2-10 P2 High temperature alarm value 80°C/176°F -50~120°C/-58~248°F P3 Low temperature alarm value -50°C/-58°F -50~120°C/-58~248°F P4 Temperature calibration value 0 -10.0°C~10.0°C P5 Compressor delay time 0 0-60Min P6 Display mode C C/F P0: working modeThis setting is mainly set to the value when the thermostat is used for the first time. If it is used for heating, it should be set to H. If it is used for cooling, it should be set to C.P1: hysteresis settingThe hysteresis is the difference required when the thermostat reaches the set temperature and stops working again. For example, if we set the heating mode to a temperature of 37-40 degrees, then the difference is 3P2: high temperature alarm valueWhen the temperature reaches the set value, there will be an alarm action and stop working.P3: low temperature alarm valueWhen the temperature is lower than the set value, there will be an alarm action and stop working.P4: temperature correctionThese functions are used for temperature calibration. If there is a deviation between the detected temperature and the actual temperature, some functional effects can be used. The positive value = measured value + corrected value. For example, we measure the temperature at 25.6 degrees and actually 25.8 degrees. P4 can be used. Set to 0.2 then the final temperature is 25.6+0.2=25.8P5: delayed startThis function is generally used for compressor refrigeration. If you purchase some thermostats for the refrigerator freezer, this value must be set. According to the compressor back pressure, the general setting is 3-6 minutes.P6: C/F conversionIf you want to change to F value, change the unit to F, the unit display light is on. If you want to change it to C value, change the unit to C, the unit display light is not bright. If you want to convert quickly, exit the display, long press You can quickly convert units by adding 3 seconds.Package Included:1 x Temperature Controller+Waterproof Sensor Shipping PolicyPayment MethodReturns PolicyShipping Policy 1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand. 2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders. 3.All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.Payment Method 1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase. 2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances. 3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.Returns Policy 1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase. 2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse. 3. Please include your eBay ID and item number with any email requests.

Price: 11.27 USD

Location: JAMAICA, NY

End Time: 2024-07-28T09:24:41.000Z

Shipping Cost: 0 USD