1x THERMAL FUSE FOR NESPRESSO AEROCCINO 3 4 PLUS FROTHER REPAIR KIT REPLACEMENT

Description: YOU ARE ORDERING A REPAIR KIT FOR NESPRESSO AEROCCINO 3 FROTHER LIKE FOR LIKE THERMAL (ECONOMY) FUSE REPAIR KIT PLEASE NOTE IF YOUR FROTHER WORKS ON COLD THEN THIS IS NOT GOING TO HELP YOU, YOUR ELEMENT HAS PROBABLY BURNT OUT!! PLEASE READ THE WHOLE DESCRIPTION: If your frother has stopped working completely and there is a brown carbon / caramelised deposit on the base, the thermal fuse has most likely blown. If this is what has happened, the machine will never work again until the fuse is replaced. NESPRESSO WOULD LIKE YOU TO either: RETURN THE MACHINE TO A SERVICE CENTRE (WHO WILL SIMPLY REPLACE THE FUSE) OR BIN IT and BUY A NEW MACHINE. YOU DON'T NEED TO DO either, USUALLY IT'S A SIMPLE DIY REPAIR. This is a repair kit which addresses the themal fuse blowing. We have 2 kits available for the Aeroccino (one (this listing) is a single use thermal fuse and the other is an automatic resetting fuse (item number 292274640385)). THIS KIT INCLUDES: A length of clear heat-shrink tubing for insulation 4 x female crimp / joiners (2 required and 2 spares) 1 x single use thermal fuse 10cm electrical solder wire (we strongly recommend that this fuse is soldered into place) This listing is for a "like for like" repair, a single use (once blown it needs replacing) fuse. At item number 292274640385 we also have a resetting fuse UPGRADE kit (with once fitted, if the thermal fuse blows/trips, simply clean the base of the inside of the machine (bleach works best I find) and rest / leave it for a few minutes and it will reset). TOOLS NEEDED: T10 TORX or 2.0mm HEXAGONAL or 5/64" HEXAGONAL ALLEN KEY / SCREWDRIVER BIT PLIERS CABLE SNIPS SOLDER IRON You can do this! PLEASE LOOK AT ALL THE PICTURES AS THEY ARE THERE TO GUIDE YOU. With the right tools, fitting this new fuse is EASY. STEPS 1-3 CAN BE DONE TO CHECK THE FUSE IS INDEED THERE BEFORE ORDERING REPAIR KIT. OK, Here we go: Remove the 2 bolts on the base of the machine (they are triple fin type security heads but they can be removed with a T10 TORX or 2.0mm HEXAGONAL or 5/64" HEXAGONAL ALLEN KEY / SCREWDRIVER BIT or a tight fitting flat screwdriver) with 3-4 turns.The base plate is an integral part of the whole (red in this picture) base unit. Gently pull / separate the base from the machine body (DO NOT TURN IT MORE THAN A COUPLE OF DEGREES BACK AND FORTH TO LOOSEN IT), a warm/ hot wet cloth will help as it is often stuck with dried milk.Remove the silicone on/off button from the frother body (it just pushes out like a cork from inside)Take as many photos as you want before going farther so you can check the position of all wires and components when it comes to re-assembly.Cut the wires on either end of the fuse and remove the fuse along with the clear plastic sleeving.Slide a new length of sleeving on to one of the red cables and move it along away from the end so that it will not be touched by the solder iron.Size and trim up the new fuse wires so that they match the length of the original. Using the small crimps/joiners (there are 4 so that you can have another go if the lengths are wrong) crimp the fuse in place. If you are happy with the lengths, solder the joins in place. Slide the shrink tubing over the exposed wires and using the solder iron, shrink it in place on either side of the new fuse (TAKING CARE NOT TO PUT HEAT TOO NEAR YOUR NEW THERMAL FUSE OR IT WILL BLOW).Replace the fuse to it's original positionRe-assemble BY UN-DOING STEPS 1 TO 3 IN ORDER 2,1 THEN 3Put your tools away and make yourself a REWARDING cappuccino. Please re-check all the pictures and diagrams before you start the job. Although it's not essential to solder (as the joiners we supply can be crimped into place as a solderless repair) we do believe that a soldered join is by far the best and we strongly recommend that it is soldered and for that reason include solder in the kit. n.b. PLEASE read the following carefully before ordering To avoid any doubt, this listing is for a REPAIR KIT, NOT A FROTHER. If your frother is spinning and not heating, then it is NOT fused and this kit wont help you. Some frothers are refurbished by removing / bypassing this safety feature and can often be sold as new. This thermal fuse is the frother's last line of defence from overheating and self destruction. It NEEDS to be in place to protect your heater element. You can take your machine apart BEFORE you order the repair kit to be sure the machine either has a fuse and is still in situ in your machine. If it has no fuse or it been removed already, then this kit won't help you as your element has possibly gone (which can't be repaired as it is housed in a mineral based enamel which requires temperatures of 1400+ to melt) or some other component/s has/have failed (this can be fixed in theory, but not such an easy fix as it requires testing of individual components). Some frothers which look just like the aeroccino 3 on the outside have a different circuit board and some (esp. refurbished) machines are either not fitted with a temperature fuse or have had it removed. This fix will not repair your machine however, one can add it as an aftermarket upgrade to protect the heater element. n.b Just to be sure there is no misunderstanding, a new fuse will NOT stop burnt milk, only regular cleaning after every use will stop the base from burning the milk. However, the lack of cleaning and burnt milk that comes as a consequence WILL eventually blow your thermal fuse. This kit works perfectly with the Aeroccino Plus and Aeroccino4 but it is quite a different task to open an Aeroccino4. We recommend you open your Aeroccino4 first before ordering, there are some good you-tube videos on how to do it. Search in a browser for p9xC9jnJSRs Happy customer message: thank you friend, I received the complete repair kit to fix my aeroccino and I did everything as you are in the place and it worked, thanks again for everything you returned part of the happiness of my girl lol n.b. All measurements are approximate. ******************* FOR MORE BARGAINS AND INTERESTING ITEMS, PLEASE VISIT OUR STORE FOR A BROWSE AROUND: LOVELIFE3BAY3LLovelife3BAY sell quality home improvement products electrical fuses lighting DIY Motorcycle seat cover repair kits architectural furniture lock window door handle hinges brackets brass chrome finishes mesh aluminium upvc pvc insect screen buttons toe-socks plastic electronic plug adapters and fishing tackle. For multiple purchases, a COMBINED POSTAGE INVOICE should be sent automatically. If you are happy with the invoice please feel free to proceed with payment. If it doesn't happen automatically or there is ANY issue with the automatic invoice, PLEASE WAIT to receive an invoice or contact us BEFORE you make payment. There are always ways of improving the service quality, and we endeavour to continually improve, so please feel free to tell us how we can. Thank you for your time to read this. Our shipping charge includes: • collection service to ensure post is collected virtually EVERY working day • packaging materials • postage/ delivery/ courier *******************

Price: 3.69 GBP

Location: Aberdeen

End Time: 2024-03-21T09:43:25.000Z

Shipping Cost: 4.21 GBP